Category: Micro Controller Projects

This information is about  Bike Renting System  project.

The serial data is again received by the controller and here the code that is send with a that format is converted in to ASCII conversion and this send to the system. There in the system the time and take of the bike holder will be  recorded and the status of the bike is noted.  the cards that are assigned to the bikes is passive ID cards. This is passive cards doesn’t have any power. This is activated with the help of the frequency that is generated by the reader itself.

The reader eill read the data and send that to the controller will store the data in the EEPROM. This is to keep the track of the vehicle details and then again it is send to the system through RS232 protocol. This is maintained again in the data base of the system. The details like the total kilometers travelled and other details are recorded manually after the delivery. The time and rent for the time is given in the system.

download Bike Renting System  abstract.

Normally in the field it is not possible for a person to continuously monitor the condition and the water level in the field. The water level that is in the field has to be monitored and the level of the sump has to be checked and then the motor has to work accordingly. This every this in divided in different sub networks and then according to the levels and status of the field the motor will run under condition. Here actually we are using a wireless network.

That is RF communication system with 433MHz frequency with an address to match the identity. This actually monitors the humidity in the field and water level in the tank and the currents and voltage of the motor. In the field it is common to find that the current and voltage are not always the same.

So that we check the current s and voltages and then if the voltages and currents are at required level then it immediately transfers the signal to the motor to switch it on. This checks not only the current and voltage values even the level of the water that is present. If the level of the water is at a sufficient level then it automatically switches on the motor.

At the same time it even monodies the condition dint he field. If the water level is sufficient for that time then it instructs the motor to switch it off. This is all done with a wireless network since it is difficult to plant and wire the complete field for the application in this manner. The address has to be matched with the relevant master unit and the master unit controls the remaining part.

A complete network is been implemented in this field with a wireless system. The motor speed is also controlled with a pulse width modulation technique because normally these motors in the field do not have a slow start to regulate the initial currents in the motor.

download A Wireless Design Of Low Cost Irrigation System project abstract.

BLUETOOTH DATA ACQUISITION SYSTEM BASED ON AVR  is used for industrial application for remote operation of different units and monitors the operation of different equipments. Bluetooth has faster rate of data transfer so that the changes in the equipment can be noticed immediately. Atmel Versatile RISC processor which is incorporated in this module will take the control lead part. The slave and master communication is done here. The master will transfer the address and the slave will check the address and if the address is matched with the assigned address of the slave then the communication network bonds the master and slave. In industries most of the equipments require the conditions and parameters of it continuously.

If the Bluetooth protocol is implemented in this place the then the data transfer can be done from the place where the module is placed to the control room. The module will transfer different parameters continuously with out any mismatch or interference of any external disturbances. This replaces the all cable protocol which reduces the place and external interference. The AVR controller has internal accesses to analog input so which is having a ten bit resolution in which we can get good precision compared to that of 8 bit controller and converters.

The speed of the controller is also high so that it can easily match with the speed of the Bluetooth module. The communication network between these to devices is linked with the serial port which in inbuilt in the AVR controller. The data transfer and the communication link between the master and slave with the Bluetooth protocol. The master unit is connected to the computer is have the log status of all the parameters continuously for further verification and control of the equipment for the master control room.

APPLICATIONS:

• HOME AUTOMATIONS
• INDUSTRIAL CONTROLS
• CONSUMER ELECTRONICS

HARD WARE:

• AVR PROCESSOR
• POWER SUPPLAY UNIT
• LCD DISPLAY
• FAN SPEED CONTROLLING
• BOILER UNIT
• GENERATOR UNIT
• COMMUNICATION PORT
• BLUETOOTH MODULES(TX/RX)
• COMPUTER

SOFTWARE:

• CODEVISION AVR(IDE TOOL)
• STK200/300 PROGRAMMER
• SERIAL COMMUNICATION PORT
• SIMULATION TOOLS

download  Bluetooth Data Acquisition System Based On Avr  abstract.

The robots are connected in such a way that the communication between them will be in a bonded link that they are always transferring the data so avoid the obstruction and transfer the accurate data from the place it stays. A robot is equipped with a wireless camera to transfer the video data of the location where the robot goes. That is linked with the second robot to detect the presence of metal, heat and presence of humidity from the locations. The data that is collected by the second robot is sent to the first one and this alerts the user from the location there. This is done to make a systematic manner to incorporate the network between to Zigbee modules  in an efficient manner for a low power consumption and pinpoint connection  for fast data transfer.

The network type used here will be a pinpoint type of network for communication since we have two modules to communicate. The rugged nature for the robots are in such a way that they can travel in different places. The sense the metal with a proximity sensor that sensory signal finds the strength of the material and the send the same to the master other robot to find the location of that place. If the presence of heat around that are it detects that and send that to the robot and gives a continuous image transfer to the system. This heat is detected with thermistor and then the signal is converted in to digital signal and that is read by the controller and the same is transfer to the other robot. This forms a link to the both the robots  for continuous transfer of the data between the robots to from a Zigbee network.

APPLICATIONS:

• Automobiles
• Aircrafts fleet management
• Remote vending
• Remote control
• Security systems
• Tele-services
• Consumer electronics
• Home automations
• Industrial controls
• Military,
• Navigation

HARD WARE:

• AVR PROCESSOR
• POWER SUPPLAY UNIT
• LCD DISPLAY
• FAN SPEED CONTROLLING
• BOILER UNIT
• GENERATOR UNIT
• COMMUNICATION PORT
• X-BEE(TX/RX)
• COMPUTER

SOFTWARE:

• CODEVISION AVR(IDE TOOL)
• STK200/300 PROGRAMMER
• SERIAL COMMUNICATION PORT
• SIMULATION TOOLS

download Robotics Wireless Network  abstract.

Control area network is a network system for connecting different nodes and controlling it by transferring data from one node to another. Here the mode of data transfer will be from each and every nodal address mostly can bus is used for automobiles, industrial application and controls. 

 This will consume very less power compared to another network connection we give a specific address to each and every location where the CAN node is fixed with this specific address each is communicated. The data what we want to display will be predefined one and that is transmitted to the location after transmit we can get an acknowledgement from that place that the complete data s been received.

Hardware components:

• At mega 16
• CAN Controller MCP2515
• CAN trans Receiver MCP2551
• Temperature Sensor
• LCD 

SOFTWARE:

• Code vision AVR IDE tool
• Embedded c programming
• Functionality of the above components

APPLICATIONS:

• Automation
• Automotive devices
• Remote application
• industrial application 

Skill set:

• Functionality of all above components
• Embedded C programming
• Can bus protocol